background image

CLCH-SVX05A-GB

General
Information

©American Standard Inc. 2002

Foreword

These installation, operation, and

maintenance instructions are given as a

guide to good practice in the installation,

commissioning into service, operation,

and periodic maintenance by the user, of

CLCH Air Handling Units. They do not

contain the full service procedures

necessary for the continued successful

operation of this equipment. The services

of a qualified service technician should be

employed through the medium of a

maintenance contract with a reputable

service company.

Warranty

Trane’s standard warranty covers the

equipment. It does not cover damage due

to misuse, lack of maintenance, or failure

to comply with the manufacturer's

instructions or recommendations.

Receiving/Handling

On arrival, inspect the unit before signing

the delivery note. Specify any damage on

the delivery note, and send a registered

letter of protest to the last carrier of the

goods 

within 72 hours

of delivery. Notify

the local Trane sales office at the same

time. The unit should be totally inspected

within 15 days of delivery. If any

concealed damage is discovered, stop

unpacking the shipment. Take photos of

the damaged material if possible. Notify

the carrier immediately by phone and

registered mail. Notify the local Trane

sales office. Concealed damage must be

reported 

within 15 days

of delivery.

About This Manual

Warnings appear at appropriate places in

this instruction manual. Your personal

safety and the correct operation of this

machine require that you follow the

warnings carefully. The manufacturer

assumes no liability for installations or

servicing undertaken by unqualified

personnel.

About The Unit

The information contained in this manual

applies to units designated CLCH

Содержание CLCH

























Отзывы: