Trackmaster TMX428 страница 90 Скачать руководство пользователя

Страница: 90 / 159

Troubleshooting

Ch. 9

TRACKMASTER

TMX428 TMX428CP & TMX58 Service Manual

317-160-406 Rev 4

May 2021

Smart Power Supply Error Code 9 Flow Chart 1R “Start Belt Command Received During

Initialization”

Smart Power Supply Error Code 10

Consult the factory for trouble shooting.

Full Vision Inc.
3017 Full Vision Drive
Newton, KS 67114 USA
http://www.full-vision.com
Phone: (316)-283-3344
Fax: (316)-283-9522
Email:

[email protected]

Is the Red LED D13

flashing 9 times with

4 second pause on the

Smart Power Supply

FG0495?

Yes

Turn the treadmill power switch
OFF (O).

Is the Red LED D13

on the Smart Power

Supply FG0495 on

continuously?

Yes

Is the Red LED D13

flashing on the

Smart Power Supply

FG0495?

Yes

Treadmill should

be operational.

Send a Start Belt Command or Press
Start if equipped with controller
increase speed to 10

MPH.

With the treadmill

running at 10.0 MPH

for 1 minute is the

Red LED D13 on?

Return Treadmill

to service.

Replace Interface
cable.

Yes

Inspect interface cable between
the Treadmill & Stress System
cables for damage.

Turn the treadmill power switch ON (-).

Is the RS232 or

USB Interface

cable damaged?

Содержание TMX428
































































































































































Результаты поиска

Содержание TMX428

Отзывы:

Похожие инструкции для TMX428

Бренды по названию

Популярные бренды

Trackmaster TMX428, Руководство по обслуживанию

Результаты поиска

Содержание TMX428

Отзывы:

Похожие инструкции для TMX428

Бренды по названию

Популярные бренды