Trackmaster TMX428 страница 83 Скачать руководство пользователя

Страница: 83 / 159

TRACKMASTER

Ch. 9

Troubleshooting

317-160-406 Rev 4

TMX428 TMX428CP & TMX58 Service Manual

May 2021

Smart Power Supply Error Code 3 Flow Chart 1L “Missing Speed Signal From Motor

Controller”

Is the Red LED D13

flashing 3 times with

4 second pause on the

Smart Power Supply

FG0495?

Yes

Turn the treadmill power
switch OFF (O).

Is the Red LED D13

on the Smart Power

Supply FG0495 on

continuously?

Yes

Is the Red LED D13

flashing on the

Smart Power Supply

FG0495?

Yes

Treadmill should

be operational.

Send a Start Belt Command
or Press Start if equipped
with controller.

Did the

running belt

start?

Return Treadmill

to service.

Replace Drive
PC2303-012-N
317-160-196

Yes

Verify the harness between Drive PC2303-012-N
and Smart Power Supply FG0495 is properly
connected and not damaged.

Was the harness

damaged?

Turn the treadmill power
switch ON (-).

Was the harness

properly

connected?

Replace Harness
317-160-208

Yes

Connect harness.

Verify the harness between Motor
PMC5FA-00101-03 and Drive PC2303-012-N
is properly connected and not damaged.

Yes

Was the harness

damaged?

Was the harness

properly

connected?

Replace Motor
317-160-197

Yes

Connect harness.

Yes

Содержание TMX428
































































































































































Результаты поиска

Содержание TMX428

Отзывы:

Похожие инструкции для TMX428

Бренды по названию

Популярные бренды

Trackmaster TMX428, Руководство по обслуживанию

Результаты поиска

Содержание TMX428

Отзывы:

Похожие инструкции для TMX428

Бренды по названию

Популярные бренды