Toyota AURION 2013 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 371

background image

63

Safety information

BEFORE DRIVING

CHILD RESTRAINT

Child restraint requirements

NOTICE

The Australian Road Rules mandate the following age-based requirements for child
restraint and booster seats.

• Children under 6 months

must use an approved, properly fastened and adjusted

rearward facing restraint.

• Children aged between 6 months and under 4 years

must use an approved,

properly fastened and adjusted rearward facing child restraint OR a forward facing
restraint.

• Children aged between 4 years and under 7 years

must use an approved, properly

fastened and adjusted forward facing restraint or an approved boosted seat which
is properly positioned and fastened.

• If a car has two or more rows of seats,

children under 4 years

must not travel in

the front seat.

• If all seats, other than the front seats, are being used by children under 7 years

,

children aged between four and six years (inclusive) may travel in the front seat,
provided they use an approved restraint or booster seat that is properly fitted.

Child restraint precautions

Toyota strongly recommends the use of child restraints that meet Australian Standard
AS1754-2010 or later.
If a child is too large for a child restraint system, the child should sit in the rear seat and
must be restrained using the vehicle’s seatbelt. Refer to “Seatbelts” on page 31.

CAUTION

• For effective protection in automobile accidents and sudden stops, a child must

be correctly restrained, using a seatbelt or child restraint system depending on the
age and size of the child. Holding a child in your arms is not a substitute for a child
restraint system. In an accident, the child can be crushed against the windscreen,
or between you and the vehicle’s interior.

• Toyota strongly recommends the use of a correct child restraint system which

conforms to the size of the child, installed on the rear seat. According to accident
statistics, the child is safer when correctly restrained in the rear seat than in the
front seat.

• Never install a rear-facing child restraint system on the front passenger seat. In the

event of an accident, the force of the rapid inflation of the front passenger airbag
can cause death or serious injury to the child if the rear-facing child restraint
system is installed on the front passenger seat.

• Australian law requires the use of an upper anchor strap on child restraint systems.

Not for Reproduction

«
...
83
84
85
86
87
...
»

Содержание AURION 2013




















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AURION 2013

Бренд: Kargo Master Страницы: 13

Бренд: Kargo Master Страницы: 21

Бренд: Kargo Master Страницы: 4

Бренд: Condor Страницы: 2

Бренд: CALIMA Страницы: 9

2011 A3 Sportback

Бренд: Audi Страницы: 29

1966 Spider 105

Бренд: Alfa Romeo Страницы: 46

Бренд: Bestop Страницы: 31

Бренд: Paser Страницы: 2

Бренд: Xblitz Страницы: 56

Бренд: POOL-LINE Страницы: 2

Бренд: Gator Страницы: 6

Бренд: F.lli Menabo Страницы: 16

Escalade 2004 Escalade ESV

Бренд: Cadillac Страницы: 472

Бренд: Master Tailgaters Страницы: 10

Бренд: CSL Страницы: 8

Бренд: Kuda Страницы: 3

Бренд: Volvo Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды