Toyota A442F Скачать руководство пользователя страница 80

Страница: 80 / 143

AT-67

AUTOMATIC TRANSMISSION - SECOND BRAKE

2. INSPECT BUSHING OF CENTER SUPPORT

Using a dial indicator, measure the inside diameter.

Standard inside diameter:

35.000-35.025 mm (1.3780-1.3789)

Maximum inside diameter:

35.08 mm (1.3811 in.)

If the inside diameter is greater than the maximum,

replace the center support.

3. INSPECT BUSHINGS OF FRONT PLANETARY SUN

GEAR
Using a dial indicator, measure the inside diameter.
Standard inside diameter:

25.000-25.021 mm (0.9842-0.9851 in.)

Maximum inside diameter:

25.070 mm (0.9870 in.)

If the inside diameter is greater than the maximum,
replace the front planetary sun gear.

SECOND BRAKE ASSEMBLY

1. INSTALL OIL SEAL RINGS

(a) Coat the two oil seal rings with ATF.
(b) Contract the oil seals, and install then onto the center

support.
NOTICE: Do not spread the ring ends more than neces-
sary.

HINT: After installing the oil seal rings, check that

they rotate smoothly.

2. INSTALL SECOND BRAKE PISTON
(a) Coat new two 0 —rings with ATF, and install them on

the brake piston.

(b) Align the protrusions of the brake piston with the

grooves of the center support.

both hands.
NOTICE: Be careful not to damage the O —rings.

Содержание A442F
















































































































































Результаты поиска

Содержание A442F

Отзывы:

Toyota A442F, Руководство по ремонту, Страница: 80 / 143

Результаты поиска

Содержание A442F

Отзывы: