Toyota A442F Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 143

Toyota A442F Скачать руководство пользователя страница 45

AT-32

AUTOMATIC TRANSMISSION - COMPONENT PARTS REMOVAL

GENERAL NOTES

The instructions here are organized so that you work on only one component group at a time.
This will help avoid confusion from similar —looking parts of different subassemblies being on
your workbench at the same time.
The component groups are inspected and repaired from the converter housing side.
As much as possible, complete the inspection,repair and assembly before proceeding to the next
component group. If a component group can not be assembled because pats are being ordered,

be sure to keep all parts of that group in a separate container while proceeding with disassembly,

inspection, repair and assembly of other component groups.

Recommended fluid of the automatic transmission is ATF type DEXRON

GENERAL CLEANING NOTES:

1. All disassembled parts should be washed clean with any fluid passages and holes blown through

with compressed air.

2. when using compressed air to dry parts, always aim away from yourself to prevent accidentally

spraying automatic transmission fluid or kerosene on your face.

3. The recommended automatic transmission fluid or kerosene should be used for cleaning.
PARTS ARRANGEMENT:

1. After cleaning, the parts should be arranged in proper order to allow performing inspection,

repairs and reassembly with efficiency.

2. When disassembling valve body, be sure to keep each valve together with the corresponding

spring.

3. New disc for the brakes and clutches that are to be used for replacement must be soaked in

transmission fluid for at lease fifteen minutes before assembly.

GENERAL ASSEMBLY:

1. All oil seal rings, clutch discs, clutch plates, rotating parts, and sliding surfaces should be coated

with transmission fluid prior to reassembly.

2. Make sure that the ends of snap ring are not aligned with one of the cutouts and ate installed in

the groove correctly.

4. If worn bushing is to be replaced, the subassembly containing that bushing must also be replaced.
5. Check thrust bearings and races for wear or damage. Replace if necessary.
6. Use petroleum jelly to keep parts in place.

«
...
43
44
45
46
47
...
»

Содержание A442F
















































































































































Отзывы:

Нет отзывов