Toyota A442F Скачать руководство пользователя страница 120

Страница: 120 / 143

AT-107

AUTOMATIC TRANSMISSION - COMPONENT PARTS INSTALLATION

5. CHECK PISTON STROKE OF FIRST AND REVERSE

BRAKE

Using SST and a dial indicator, measure the piston

stroke by applying and releasing the compressed air
392 - 785 kPa ( 4 - 8 kgf - cm

. 57 - 114 psi) as

shown.
SST 09350-36010(09350-061 20,09350-061 30)
Piston stroke:

3.3-3.8 mm (0.130-0.150 in.)

If the piston stroke is not as specified, select another

flange.

HINT: there are three different thicknesses for flange.

6. INSTALL PLANETARY GEARS, ONE - WAY

CLUTCH AND OUTPUT SHAFT ASSEMBLY

(a) Place the transmission case on a cylinder.
(b) Install the rear planetary carrier and output shaft as-

sembly to the transmission case.

carrier.

HINT: Use two 6 mm (1 mm pitch) bolts. Do not screw

over 5 revolutions.

(d) Align the spline of the one —way clutch with the spline

groove of the transmission case.

(e) Install the front planetary carrier and one —way clutch

assembly into the transmission case.

HINT:

• Mesh the spline of the front planetary carrier

with the flukes of the discs by rotating and pus-

hing the front planetary carrier clockwise.

• If the front planetary carrier will not rotate clo-

ckwise, check the installation of the one —way
clutch.

(f) Remove the two bolts from the front planetary carrier.

Содержание A442F
















































































































































Результаты поиска

Содержание A442F

Отзывы:

Toyota A442F, Руководство по ремонту, Страница: 120 / 143

Результаты поиска

Содержание A442F

Отзывы: