Toyota A442F Скачать руководство пользователя страница 136

Страница: 136 / 143

AT-123

AUTOMATIC TRANSMISSION - COMPONENT PARTS INSTALLATION

37. INSTALL OIL PAN
(a) Remove any packing material and be careful not to

drop oil on the contacting surface of the transmission
case and oil pan.

(b) Apply seal packing to the oil pan.

Seal packing: Part No. 08826 - 00090, THREE BOND

1281B or equivalent

Torque: 6.9 Nm (70 kgfcm, 61 in.lbf)

38. INSTALL OIL PAN PROTECTOR

Install the protector with the four bolts.

39. INSTALL TRANSFER ASSEMBLY

Install the transfer assembly with six bolts.

40. INSTALL TRANSMISSION HOUSING

(a) Install the transmission housing with the eight bolts.

NOTICE: Be careful do not dammage the two O —rings

around the oil pump body when installing the transmis-
sion housing.
Torque: 64 Nm (650 kgfcm, 47 ftlbf)

(b) Install the throttle cable to the transmission case with

the bolt.

4 1 . INSTALL TWO TRANSMISSION OIL COOLER

UNIONS

(a) Coat new O —rings with ATF, and install it to each

union.

(b) Install the two unions.

Torque: 29 Nm (300 kgfcm, 22 ftlbf)

Содержание A442F
















































































































































Результаты поиска

Содержание A442F

Отзывы:

Toyota A442F, Руководство по ремонту, Страница: 136 / 143

Результаты поиска

Содержание A442F

Отзывы: