Toyota A442F Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 143

Toyota A442F Скачать руководство пользователя страница 22

AUTOMATIC TRANSMISSION - OPERATION

AT-9

WARNING AND INDICATOR LIGHTS

A.T FLUID TEMPERATURE WARNING SYSTEM

The ECT ECU detects the transmission fluid temperature by means of a fluid temperature sensor
fitted to the union. The transmission fluid may become extremely hot when the vehicle is under
and extreme load, as when driving on sand or climbing uphill. Should the fluid temperature
increases above 150 °C (302°F), the ECT ECU lights the warning light located the combination
meter. The light goes off when the temperature falls below 120 °C (248 °F).

A.T.P. (Automatic Transmission Parking) INDICATOR

The rear propeller shaft and rear wheels are free even when the transmission shift lever is set to
"P" as long as the transfer shift lever is in "neutral" position. The A.T.P. indicator lights up to warn
the driver that the propeller shaft and wheels are not locked. If the A.T.P. indicator light does on,

the transfer shift lever should be shifted to out of "N" position.

«
...
20
21
22
23
24
...
»

Содержание A442F
















































































































































Отзывы:

Нет отзывов