Toyota A442F Скачать руководство пользователя страница 62

Страница: 62 / 143

AUTOMATIC TRANSMISSION - OVERDRIVE UNIT

AT-49

10. INSTALL OIL SEAL RINGS

(a) Coat the two oil seal rings with ATF.
(b) Contract the oil seals, and install them onto the O/D

case.
NOTICE: Do not spread the ring ends more than neces-
sary.

HINT: After installing the oil seal rings, check that

they rotate smoothly.

1 1 . INSTALL OVERDRIVE BRAKE PISTON

(a) Coat new two O —rings with ATF, and install them on

the brake piston.

(b) Align the protrusions of the brake piston with the

grooves of the O/D case.

hands.
NOTICE: Be careful not to damage the O—rings.

12. INSTALL PISTON RETURN SPRING

(a) Place the return spring on the brake piston.

(b) Place SST on the spring on the spring seat, and

compress the return spring with a shop press.

SST 09350-36010(09350-06020)

HINT: Be sure the end gap of the snap ring in not

aligned with the cutout portion of the O/D case.

Содержание A442F
















































































































































Результаты поиска

Содержание A442F

Отзывы:

Toyota A442F, Руководство по ремонту, Страница: 62 / 143

Результаты поиска

Содержание A442F

Отзывы: