Toyota A442F Скачать руководство пользователя страница 53

Страница: 53 / 143

AT-40

AUTOMATIC TRANSMISSION - OVERDRIVE UNIT

(b) Remove the flange, three discs and three plates.

5. REMOVE PISTON RETURN SPRING
(a) Place SST on the spring seat, and compress the return

spring with a shop press.
SST 09350-3601 0(09350-0601 0)

(b) Using snap ring pliers, remove the snap ring.
(c) Remove the spring seat and twenty — four return

springs.

6. REMOVE OVERDRIVE DIRECT CLUTCH PISTON
(a) Place the oil pump onto the torque converter, and

then place the O/D direct clutch onto the oil pump.

(b) Hold the clutch piston with hand, apply compressed

air into the oil hole of the oil pump to remove the
clutch piston.

(b) Remove the two O —rings from the clutch piston.

7. REMOVE OIL SEAL RING FROM RING GEAR

FLANGE

8. REMOVE RING GEAR FLANGE
(a) Using a small screwdriver, remove the snap ring.

Содержание A442F
















































































































































Результаты поиска

Содержание A442F

Отзывы:

Toyota A442F, Руководство по ремонту, Страница: 53 / 143

Результаты поиска

Содержание A442F

Отзывы: