Toyota A442F Скачать руководство пользователя страница 126

Страница: 126 / 143

AUTOMATIC TRANSMISSION - COMPONENT PARTS INSTALLATION

AT-113

17. INSTALL FRONT CLUTCH ASSEMBLY

(a) Coat the race with petroleum jelly, and install it onto

the rear clutch drum.

HINT: Race diameter

(b) Coat the bearing with petroleum jelly, and install them

onto the front clutch hub.
HINT: Bearing and race diameters

case.

HINT: Mesh the spline of the front clutch hub with the

flukes of the discs by rotating and pushing the front

clutch drum clockwise or counterclockwise.

18. CHECK CORRECT INSTALLATION OF FRONT

CLUTCH ASSEMBLY

(a) Place SST on the installation surface of the oil pump.

SST 09350-36010(09350-06090)

(b) Using calipers, measure the distance between the

tops of SST and the clutch drum.

If the distance corresponds to that during disasse-
mbly, the front clutch assembly is installed correctly.

19. TEMPORARILY INSTALL OVERDRIVE CASE AS-

SEMBLY

(a) Remove the oil seal ring from the input shaft
(b) Coat the race and bearing with petroleum jelly, and

install the spacer and them onto the front clutch
drum.

HINT: Bearing and race diameter

Содержание A442F
















































































































































Результаты поиска

Содержание A442F

Отзывы:

Toyota A442F, Руководство по ремонту, Страница: 126 / 143

Результаты поиска

Содержание A442F

Отзывы: