TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 80

TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 63

Maintenance

TOX_Manual_Powerpackage_line-Q_en

63

ü

System is in maintenance position.
See

Set system to maintenance position, Page 59

.

1.

Remove venting plate with locking wire.

2.

Unscrew knurled cap of the oil filling nipple.

3.

Vent filling hose of the oil pump.

4.

Install filling hose of the oil pump on oil filling nipple.

5.

CAUTION!

Splashing oil! Open vent screw slowly!

Unscrew corresponding vent screw (see table "Venting point according
to installation position") by 2 turns.
- OR -
Unscrew corresponding high pressure measuring connection cover
(see table "Venting point according to installation position:") and push
in with a blunt object (e.g. a pin).

6.

Continue to fill until oil escapes from the open vent hole free of bubbles.

7.

CAUTION!

Risk of injury and risk of slipping from leaking oil! Absorb oil

immediately and without residue!

8.

Wait 10 min. Afterwards, repeat filling procedure until oil escapes from
the open vent hole free of bubbles.

9.

Unscrew filling hose of the oil pump.

10. Tighten vent screw.

- OR -
Close high pressure measuring connection.

11. Screw in knurled cap of the oil filling nipple.

12. Install venting plate.

13. Fasten locking wire.

14.

NOTE!

Device damage due to overfilling!

Lower oil level.
See

Lowering of oil level, Page 64

«
...
61
62
63
64
65
...
»

Содержание Powerpackage Q Series

















































































Отзывы:

Нет отзывов