TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 5

Страница: 5 / 80

Table of contents

TOX_Manual_Powerpackage_line-Q_en

6.3.2

Installing position sensors of stroke monitoring for forward and return stroke
(ZHU) ........................................................................................................ 31

6.3.3

Installing the external linear position sensor (ZHW).................................. 33

6.3.4

Installing pressure control in the power stroke line (ZDK)......................... 35

6.3.5

Installing external power stroke connection (ZKHZ) ................................. 36

6.3.6

Installing external power stroke release (ZKHF) and power stroke deactiva-
tion (ZKHD) ............................................................................................... 37

6.3.7

Preparing external power stroke supply.................................................... 38

6.3.8

Installing the stroke frequency optimization (ZHO) ................................... 39

6.3.9

Installing the speed reduction for power stroke venting ............................ 41

6.3.10

Installing tool coupling (ZWK) ................................................................... 42

Commissioning

7.1

Safety during the commissioning .............................................................. 43

7.2

Requirements for the commissioning........................................................ 44

7.2.1

Measuring connection and control connection.......................................... 44

7.3

Avoidance of dynamic oil leakage............................................................. 45

7.3.1

Setting speed ratio of return stroke to fast approach stroke ..................... 46

7.3.2

Set the speed ratio between power stroke and power stroke venting (op-
tional) ........................................................................................................ 46

7.4

Setting control throttle 'X' .......................................................................... 47

7.5

Setting total length of stroke (optional)...................................................... 48

Operation

8.1

Safety in operation .................................................................................... 49

8.2

Requirements for operation....................................................................... 50

8.3

Operating drive.......................................................................................... 50

Troubleshooting

9.1

Safety during troubleshooting ................................................................... 51

9.2

Searching for causes of fault..................................................................... 52

Содержание Powerpackage Q Series

















































































Результаты поиска

Содержание Powerpackage Q Series

Отзывы:

TOX PRESSOTECHNIK Powerpackage Q Series, Оригинальная инструкция по эксплуатации, Страница: 5 / 80

Результаты поиска

Содержание Powerpackage Q Series

Отзывы: