TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 80

TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 47

Commissioning

TOX_Manual_Powerpackage_line-Q_en

47

7.4

Setting control throttle 'X'

The control throttle 'X' is used to set the timing of the switchover from fast
approach stroke to power stroke, and must be readjusted for each applica-
tion (e.g. tool weight drawing/pressing). The effect of the control throttle 'X'
is influenced by the system pressure and by setting an optional fast ap-
proach stroke throttle.

Fig. 9

Setting control throttle 'X'

ü

Working piston is retracted.

ü

Compressed air supply is switched on.

1.

Close control throttle 'X' when piston is retracted and impinged by turn-
ing clockwise.

2.

Extend working piston rod.

3.

Open control throttle 'X' slowly by turning counterclockwise until the
power stroke is noticeably activated on meeting a counterforce. Open-
ing the control throttle 'X' further causes the power stroke to be acti-
vated earlier.

«
...
45
46
47
48
49
...
»

Содержание Powerpackage Q Series

















































































Отзывы:

Нет отзывов