TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 80

TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 45

Commissioning

TOX_Manual_Powerpackage_line-Q_en

45

7.3

Avoidance of dynamic oil leakage

The dynamic oil leakage is based on the physical effect of drag flow: the
higher the speed, the thicker the oil film dragged along. In the case of an
unfavorable speed ratio between the fast approach stroke and return
stroke, an oil film could get into the pneumatic chambers of the Powerpack-
age.

The following applies:

The ratio of the speed between the return stroke and the fast approach
stroke must be set.

–

For setting the speed ratios, also the exhaust air dampers must be
installed on the fast approach stroke connections and the return
stroke connections.

A balanced power stroke speed.

–

For the attuned power stroke speed an exhaust air damper must
also be installed in the power stroke venting.

For the throttled power stroke speed, the speed ratios between power
stroke speed and venting of the power stroke must be set.
See

Chap. 6.3.9 Installing the speed reduction for power stroke vent-

.

The power cross sections to the Powerpackage (hose cross sections,
switching valves, maintenance unit) must at least meet the specifica-
tions in the type sheet.
For technical data and installation dimensions see the type sheet.
(

https://tox-pressotechnik.com/

)

«
...
43
44
45
46
47
...
»

Содержание Powerpackage Q Series

















































































Отзывы:

Нет отзывов