TOX PRESSOTECHNIK Powerpackage Q Series Скачать руководство пользователя страница 64

Страница: 64 / 80

Maintenance

TOX_Manual_Powerpackage_line-Q_en

10.5

Lowering of oil level

CAUTION

Environmental pollution caused by environmentally harmful liquids!

Absorb spilled liquids and remove without residue.

Dispose of liquid according to the statutory regulations.

NOTE

Damage to seal due to high oil level!

After refilling and venting, lower the oil level by a defined value (lowering
volume "ΔV").
For lowering volume "ΔV" see type plate.

Material required:

Oil pump ZP 20

System is in maintenance position.
See

Set system to maintenance position, Page 59

Drive is filled and vented.
See

Refilling oil and venting drive, Page 61

Remove venting plate with locking wire.

Unscrew knurled cap of the oil filling nipple.

Screw filling hose of the oil pump onto oil filling nipple.

CAUTION!

Risk of slipping from leaking oil! Absorb oil immediately and

without residue!
Remove oil quantity exactly according to lowering volume "ΔV".

Unscrew filling hose of the oil pump.

Install venting plate.

Screw on knurled cap of the oil filling nipple.

Fasten locking wire.

Push in oil level indicator needle.

Содержание Powerpackage Q Series

















































































Результаты поиска

Содержание Powerpackage Q Series

Отзывы:

TOX PRESSOTECHNIK Powerpackage Q Series, Оригинальная инструкция по эксплуатации, Страница: 64 / 80

Результаты поиска

Содержание Powerpackage Q Series

Отзывы: