background image

TECHNICAL SPECIFICATIONS

 

- Single phase power-supply voltage 

115 / 230  VAC 

 

- Voltage variation tolerance 

+/- 10  % 

 

- Frequency 

50 / 60  Hz 

 

- Full load amp rating 115 VAC 

16  FLA 

 

- Full load amp rating 230 VAC 

20  FLA 

 

- Max working pressure 

174  psi 

 

- Pressure adjusting rangem

in   45   psi 

  

max  95  psi 

 

- Max working temperature 

149  ˚F (65˚C) 

 

- Inlet / Outlet connections 

1 ¼

  MPT 

 

- Threaded gauge connection 

¼”  FPT 

 

- Threaded conduit connections 

½

  FPT 

 

- Electronic box enclosure 

12  NEMA 

• 

Displays when power is connected to TOTAL CONTROL unit. 

• 

In the event of a temporary power outage, TOTAL CONTROL resets automatically when 
power is restored. 

• 

Displays when pump is running. 

• 

Displays when there is a problem with the system. 

• 

Press and hold to reset for 3-5 seconds ( with a tap opened ). Green “Power on” light and 
yellow “Pump on” should display. This indicates system is operating properly. 

• 

If red “Failure” light comes back on, refer to Troubleshooting Guide. 

OPERATION

TROUBLESHOOTING

MAINTENANCE AND SPARE PARTS

- 3 - 

Operating faults 

Main causes 

Pump does not start 

Check wiring connections. 

Check suction pipe, see page 6. 

Pump turns on and off (short-cycles) 

Leakage lower than minimum flow. 

Pump does not stop 

Leakage above minimum flow. 

No water flow 

Suction problems. 

Power on 

Pump on 

Failure 

Restart

( green ) 

( yellow ) 

( red ) 

( red ) 

In the case of a fault in the electronic box, this can be replaced without removing the device as it is inter-

changeable and supplied on request. 

Further malfunctioning can be avoided by checking the features  of the device,  pump  and system  with  the 

warnings indicated in the installation guidelines. 

Содержание PCTC16F16S

















Отзывы: