Toshiba TXZ Скачать руководство пользователя

Страница: 38 / 120

TXZ Family

Flash Memory

2018-06-05

38 / 120

Rev. 2.0

Supplementary explanation

IA: ID address

ID: ID data output

PGA: Page address

BA: Block address

AA: Area address

PA: Program address (write)

PD: Program data (32-bit data)

PBA: Protect bit address

3.2.1.2. Address Configuration in the Bus Write Cycle (Data Flash)

Please refer to “Table 3.8

Address bit configuration in the bus write cycle (data flash)” with “Table 3.7

Command sequence (Data flash)”.

Specify addresses in the first bus cycle and later cycle, based on address setting of bus write cycle of normal

command.

Table 3.8 Address bit configuration in the bus write cycle (data flash)

[Normal command]

Address

Adr

[31:24]

Adr

[23:16]

Adr
[15]

Adr

[14:12]

Adr

[11:4]

Adr

[3:0]

Normal
command

Address setting of bus write cycle of normal command

0x30

“00000000”

fixed

Area

(Note)

"0”

Recommended

Command

"0”

Recommended

Note: Use “Area” fixed to “0”.

[Read/reset, ID-Read]

Address

Adr

[31:24]

Adr

[23:16]

Adr
[15]

Adr

[14:13]

Adr

[12:0]

Read

/reset

Address setting of 1

bus write cycle of read/reset

0x30

“00000000”

fixed

"0”

Recommended

ID-Read

IA: ID

Address (address setting of 4

bus write cycle of ID-Read)

0x30

“00000000”

fixed

"0”

fixed

address

"0”

Recommended

[Automatic area erasing]

Address

Adr

[31:24]

Adr

[23:16]

Adr
[15]

Adr

[14:0]

Area
erasing

AA:

Area Address (address setting of 6

bus write cycle of area erasing command)

0x30

“00000000”

fixed

Area

(Note)

"0”

Recommended

Note: Use “Area” fixed to “0”.

Содержание TXZ

























































































































Результаты поиска

Содержание TXZ

Отзывы:

Похожие инструкции для TXZ

Бренды по названию

Популярные бренды

Toshiba TXZ, Справочное руководство

Результаты поиска

Содержание TXZ

Отзывы:

Похожие инструкции для TXZ

Бренды по названию

Популярные бренды