manualshive.com logo in svg

Toshiba Tecra R10, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra R10 Скачать руководство пользователя страница 286

4 Replacement Procedure 

4.24 System board 

4.24 System board 

Removing the System board 

To remove the system board, follow the steps below and refer to Figure 4-35. 

1.

 

Disconnect the 

SW board FFC

 and 

Touch pad FFC

 from the connector 

CN9500

 

and 

CN9550

 on the system board. 

2.

 

Peel the 

INSU ODD UPPER

 to release the 

Bluetooth module harness

. 

3.

 

Remove the following 

screw

s securing the system board. 

•

 

M2.5

×

4C 

 FLAT 

HEAD 

  

×

3 

4.

 

Remove the 

system board

. 

5.

 

Turn over the system board and disconnect the 

Bluetooth module harness

 from the 

connector 

CN4440

 on the system board. 

 

 

System board 

Touch pad FFC 

Bluetooth module harness 

M2.5x4C FLAT HEAD 

SW board FFC 

CN4440 

CN9500

CN9550

INSU ODD UPPER

Figure 4-35 Removing the system board 

4-60 

[CONFIDENTIAL] 

TECRA R10 Maintenance Manual (960-708) 

Содержание Tecra R10





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды