manualshive.com logo in svg

Toshiba Tecra R10, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra R10 Скачать руководство пользователя страница 199

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 

3 Tests and Diagnostics  

 

 

3.29.3 Bluetooth 

test 

Preparation 

・

 

For the test of Bluetooth function, use the Windows program installed on the target 
computer (computer to be tested). A responder device (device for transmitting/receiving 
data) is also needed. (A mobile phone with the Bluetooth function is also available.) 

・

 

A Bluetooth card should be installed on the target computer.  Install the Bluetooth 
function by clicking [All Programs] -> [TOSHIBA] -> [Bluetooth] -> [Bluetooth Settings].  

 

Test procedure 

1.

 

Enable the Bluetooth function of the responder device. 

2.

 

Make sure the wireless communication switch of the target computer is set to “ON” 
position. 

3.

 

Right-click the Bluetooth icon on the lower right screen of the target computer. 

 

 

 

4.

 

Select “Options…”. 

 

 

TECRA R10 Maintenance Manual (960-708) 

 [CONFIDENTIAL] 

3-77 

Содержание Tecra R10





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды