Toshiba Tecra R10 Скачать руководство пользователя страница 257

Страница: 257 / 388

4.12 ExpressCard slot/KILL SW HOL ASSY

4 Replacement Procedures

Remove the

KILL SW HOL ASSY

from the

BASE ASSY

while releasing the

latche

KILL SW HOL

ASSY

Latch

Hole

BASE ASSY

Figure 4-17 Removing the KILL SW HOL ASSY

Installing the ExpressCard slot/KILL SW HOL ASSY

To install the ExpressCard slot (EXPRESSCARD CONNECTOR WITH FPC) /KILL SW HOL
ASSY, follow the steps below and refer to Figure 4-16 to 4-17.

Push the

KILL SW HOL ASSY

into the

hole

until it is latched.

CAUTION: Do not mistake the top for bottom of KILL SW HOL ASSY. As it is mounted

slantwise, if mistaking, only the switch projects and the SW function (on/off)
does not work.

Stick the

INSU EXP SLOT UP

on the

ExpressCard slot

in place.

CAUTION: When the INSU EXP SLOT UP is deformed or broken, do not reuse it.

Set the

ExpressCard slot

on the

BASE ASSY

and secure it with the following

screw

•

M2.0

S-THIN

HEAD

screw

TECRA R10 Maintenance Manual (960-708)

[CONFIDENTIAL]

4-31

Содержание Tecra R10





































































































































































































































































































































































































Результаты поиска

Содержание Tecra R10

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra R10, Руководство по обслуживанию

Результаты поиска

Содержание Tecra R10

Отзывы:

Бренды по названию

Популярные бренды