Toshiba Tecra R10 Скачать руководство пользователя страница 262

Страница: 262 / 388

4 Replacement Procedures

4.15 RTC battery

4.15 RTC battery

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used

batteries according to the laws and ordinances of your local authority.

Removing the RTC battery

To remove the RTC battery, follow the steps below and refer to Figure 4-20-1 to 4-20-2.

Disconnect the

ODD FPC

from connector

CN1950

on the system board and remove the

following screw to remove the

ODD CONN HOLD BRKT

from the BASE ASSY.

•

M2.5

FLAT

HEAD

screw

Disconnect the

RTC battery harness

from the connector

CN9300

on the system board.

Remove the

INSU RTC BATT

fixed to the

SD board

with the double-sided tape.

Open the cover of INSU RTC BATT while peeling adhered portion with the double-sided
tape and remove the

RTC battery

from the INSU RTC BATT.

RTC battery

harness

INSU RTC BATT

CN9300

CN1950

ODD CONN

HOLD BRKT

M2.5x4C FLAT HEAD

SD board

ODD FPC

Figure 4-20-1 Removing the RTC battery (1)

4-36

[CONFIDENTIAL]

TECRA R10 Maintenance Manual (960-708)

Содержание Tecra R10





































































































































































































































































































































































































Результаты поиска

Содержание Tecra R10

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra R10, Руководство по обслуживанию

Результаты поиска

Содержание Tecra R10

Отзывы:

Бренды по названию

Популярные бренды