manualshive.com logo in svg

Toshiba Tecra R10, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra R10 Скачать руководство пользователя страница 108

2  Troubleshooting Procedures  

2.17 SD card Slot Troubleshooting 

2.17  SD card Slot Troubleshooting 

This section describes how to determine if the computer's Bridge media functions are 
functioning properly. Perform the steps below starting with Procedure 1 and continuing with 
the other procedures as required. 

Procedure 1:  Check on Windows OS 

Procedure 2:  Connector Check and Replacement Check 

Procedure 1 

Check on Windows OS 

Insert a SD card into the slot. Check if the installed Windows recognizes automatically the SD 
card and the data in the SD card can be read. 

If the card is not recognized or data are not read, go to Procedure 2. 

Procedure 2 

Connector Check and Replacement Check 

Check 1 

The connection of SD system is shown in the following figure. 

 

If any of the connections is loose, reconnect firmly and repeat Procedure 1. If there 
is still an error, go to Check 2. 

Check 2 

The SD board may be defective or damaged. Replace the drive with a new one. If 
there is still an error, go to Check 3. 

Check 3 

The SD board FPC may be defective or damaged. Replace the drive with a new 
one. If there is still an error, go to Check 4 

Check 4 

System board may be faulty. Replace it with a new one following the step in 
Chapter 4

 Replacement Procedures

. 

2-58 

 [CONFIDENTIAL] 

 

TECRA R10 Maintenance Manual (960-708) 

Содержание Tecra R10





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды