manualshive.com logo in svg

Toshiba Tecra R10, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra R10 Скачать руководство пользователя страница 185

3.26 

Wireless LAN Test Program (Atheros): UNot UsedU 

3 Tests and Diagnostics

 

Check of the antenna connection 

1.

 

Confirm that the icon for wireless LAN appears at the lower right of the screen under 
the circumstances the wireless LAN communication is available. (It is no problem if a 
cross is shown on the icon.) 

 

 

2.

 

Double-click the icon. If the computer finds any AP (Access Point), the antenna 
marks like as follows will appear. It shows the antenna cables are surely connected to 
the wireless LAN card.  

 

 

3.

 

The following message will appear if the antenna cables are not connected to the 
wireless LAN card or no available access point is found. In this case, check the 
antenna cable connection to the wireless LAN card by disassembling the computer 
following the steps described in Chapter 4, Replacement Procedures. 

 

TECRA R10 Maintenance Manual (960-708) 

 [CONFIDENTIAL] 

3-63 

Содержание Tecra R10





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды