manualshive.com logo in svg

Toshiba Tecra R10, Руководство по обслуживанию

Поделиться
Скачать
Toshiba Tecra R10 Скачать руководство пользователя страница 23

1.2 System Unit Block Diagram 

1  Hardware Overview 

TECRA R10 Maintenance Manual (960-708) 

[CONFIDENTIAL]

 1-9 

The system unit is composed of the following major components: 

‰

 

Microprocessor 

The Toshiba TECRA R10 computer is equipped with an Intel

®

 Core

TM

 2 Duo 

Processor. These processors incorporate a math co-processor, a 6MB L2 cache 
memory. 
The PC comes in with one of the following speeds: 

Intel

®

 Core

TM

 2 Duo Processor (Montevina Penryn) 

•

 

SP9400(2.40GHz/) /SP9300(2.26GHz)  

These processors operate at 1066MHz bus clock (FSB). 

 

‰

 

Memory 

Two DDR2-667/DDR2-800 SDRAM slots. Memory modules can be installed to 
provide a maximum of 4GB. Memory modules are available in 512MB, 1024MB and 
2048MB sizes. 

- 200-pin small-size DIMM 
- 1.8V operation 
- DDR2-667/800 support 

‰

 

BIOS ROM (Flash memory) 

- 8Mbit (512K

×

16-bit chip) 

301KB used for Animation 

288KB used for system BIOS 

64KB used for VGA-BIOS 

64KB used for Finger Print 

32KB used for ACPI 

24KB used for booting 

16KB used for Parameter Block 

Others 

Содержание Tecra R10





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды