Toshiba Tecra R10 Скачать руководство пользователя страница 243

Страница: 243 / 388

4.7 Memory module

4 Replacement Procedures

4.7 Memory

module

Removing the Memory module

To remove the memory module, make sure the computer is powered off, follow the steps below
and refer to Figure 4-6 and 4-7.

CAUTION: When removing the memory module, make sure the computer is powered off.

Removing a memory module with the power on might damage the module or the
computer itself.

Do not touch the connectors on the memory module or on the computer. Dust

and stains on the connectors may cause memory access problems.

Never press hard or bend the memory module.

Loosen two

screws

and remove the

MEM COV ASSY

MEM COV ASSY

Screw

Figure 4-6 Removing the memory module (1)

TECRA R10 Maintenance Manual (960-708)

[CONFIDENTIAL]

4-17

Содержание Tecra R10





































































































































































































































































































































































































Результаты поиска

Содержание Tecra R10

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra R10, Руководство по обслуживанию

Результаты поиска

Содержание Tecra R10

Отзывы:

Бренды по названию

Популярные бренды