Toshiba Tecra R10 Скачать руководство пользователя страница 255

Страница: 255 / 388

4.11 BASE ASSY

4 Replacement Procedures

TECRA R10 Maintenance Manual (960-708)

[CONFIDENTIAL]

4-29

Installing the BASE ASSY

To install the BASE ASSY, follow the steps below and refer to Figure 4-13 to 4-15.

Set the

BASE ASSY

in place while setting the RGB connector side first. (See figure 4-

15).

Secure the BASE ASSY with the following

screw

•

M2.5

FLAT HEAD screw

13 (No description)

•

M2.5

FLAT HEAD screw

1 (Described as “A” in the figure)

CAUTION: Drive the fourteen screws in the order shown in the Figure 4-15.

Connect the

ExpressCard slot FPC

to the connector

CN2520

on the system board.

Turn the computer upside down.

Connect the

LCD harness

to the connector

CN5000

on the system board.

Stick the

INSU LCD HNS UP

on the

COVER ASSY

in place.

CAUTION: Do not reuse the removed INSU LCD HNS UP. Use a new one

Secure the BASE ASSY with following

screws

•

M2.5

FLAT HEAD screw

CAUTION: Drive the two screws in the order shown in the Figure 4-13.

Содержание Tecra R10





































































































































































































































































































































































































Результаты поиска

Содержание Tecra R10

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Tecra R10, Руководство по обслуживанию

Результаты поиска

Содержание Tecra R10

Отзывы:

Бренды по названию

Популярные бренды