Toshiba HWS-G1901CNMR-E Скачать руководство пользователя страница 53

Страница: 53 / 74

Domestic Hot Water Heat Pump Service Manual

Code Set point name Description

AUTO

The heat pump heats the water when required, normally using the heat pump operation.

The unit starts when the water temperature BT3 is more than 5°C below A1 (T AUTO) and

it stops when this temperature is reached. If the air temperature is out of the feasible limits,

the water is heated with the electric heater.

ECO

The heat pump consumes as low energy as possible The heat pump has a lower water

temperature set point A2 (T ECO). The heat pump heats the water to a lower temperature

compared to the other operations.

BOOST

The heat pump and the electrical heater operate simultaneously when possible. The unit

starts when the water temperature BT3 is more than 5 °C below A3 (T BOOST) and it

stops when this temperature is reached. If A3 (T BOOST) is higher than D33 (T HP max)

the compressor stops when the temperature D33 (T HP max) is reached. The remaining

temperature lift is accomplished with only the electric heater.

BACKUP

This is an emergency mode. When an error occurs, preventing the operation of the heat

pump, the water cannot be heated. On the display the possibility to activate the BACKUP

mode is asked to the user.

In BACKUP mode the water is heated up by the electric heater at a lower temperature

than the desired one.

The Legionella control is active in any case.

The unit starts when the water temperature BT3 is more than 5 °C below D13

(BACKUP T) and it stops when this temperature is reached.

SILENT

The fan speed decreases to the minimum in order to minimize the sound emission of the

unit in operation. The unit starts when the water temperature BT3 is more than 5 °C below

BT1 (T AUTO) and it stops when this temperature is reached.

HOLIDAY

The heat pump is turned off and only the LCD display is active. The heat pump does not

start when water heating is required. The compressor is OFF except during LEGIONELLA

control in which it can be activated.

The HOLIDAY mode is connected to the Hot on time function B4 (Hot on time). After the

HOLIDAY period is completed, the unit goes back to the previous mode of operation.

Note:

the unit can be turned off switching to HOLIDAY mode.

10.1.3 Temperatures

Code

Set point

name

Description

Range

Factory

setting

T AUTO

The temperature level at which the unit heats the water when the AUTO

mode is selected. The unit starts if the temperature of the water in BT3 falls

of 5 °C below the set point.

50 - 60

T ECO

The temperature level at which the unit heats the water when the ECO mode

is selected. The unit starts if the temperature of the water in BT3 falls of 5 °C

below the set point.

50 - 55

T BOOST

The temperature level at which the unit heats the water when the BOOST

mode is selected. The unit starts if the temperature of the water in BT3 falls

of 5 °C below the set point.

50 - 65

Содержание HWS-G1901CNMR-E











































































Результаты поиска

Содержание HWS-G1901CNMR-E

Отзывы:

Похожие инструкции для HWS-G1901CNMR-E

Бренды по названию

Популярные бренды

Toshiba HWS-G1901CNMR-E, Руководство по обслуживанию

Результаты поиска

Содержание HWS-G1901CNMR-E

Отзывы:

Похожие инструкции для HWS-G1901CNMR-E

Бренды по названию

Популярные бренды