![background image](http://html.mh-extra.com/html/toshiba/grl150-100-series/grl150-100-series_instruction-manual_429870016.webp)
⎯
15
⎯
6 F 2 S 0 8 2 8
385
DS_CLOSE
&
1
384
386
CB_N/O_CONT
1536
CB_OPEN
≥
1
CB_CLOSE
≥
1
CB_N/C_CONT
1537
DS_N/O_CONT
1538
DS_N/C_CONT
1539
1
387
1
DS_OPEN
≥
1
1
EXT_CB_CLOSE
1547
388
I.LINK
2052
COM5-S
528 BI1-COM-T
529 BI2-COM-T
532 BI5-COM-T
530 BI3-COM-T
531 BI4-COM-T
By PLC
By PLC
Figure 2.2.4.2 Inter-Link detection
2.2.5 Transmission
Data
The following data are transmitted every 60 electrical degrees for pilot wire communication or
every 30 electrical degrees for direct fibre optic communication to the remote terminal:
A-phase current
B-phase current
C-phase current
Sampling synchronization control signal
Synchronized test trigger signal
User-programmable commands
Sampled current data, for the current and previous samples, are transmitted to the remote terminal
in pairs.
In addition to the above data, cyclic redundancy check bits are transmitted to monitor the
communication channel. If a communication failure is detected at the local terminal, the output of
differential protection is blocked.
A synchronized test trigger signal is used to test the differential protection simultaneously at all
terminals. For details, see Section 4.2.7.4.
User programmable commands
Any signals (On/off data) shown in Appendix B can be assigned to COM1 to COM5, SUB_COM1
to SUB_COM5 and SUB2_COM1 to SUB2_COM12 as user programmable commands by using
the PLC function. The default setting is as follows:
Default signal
Command
Command
Default signal
No. Name
(send)
(receive)
No. Name
--
--
COM1-S
COM1-R1 / -R1_UF -- --
--
--
COM2-S
COM2-R1 / -R1_UF -- --
--
--
COM3-S
COM3-R1 / -R1_UF -- --
374
ICD_BLK-S
COM4-S
COM4-R1_UF
See Figure 2.2.1.1.
388 I.LINK
COM5-S
COM5-R1
1651 I.LINK-R1
390 LOCAL_TEST SUB_COM1-S
SUB_COM1-R1 1650
L.TEST-R1
(reserved) (
∗
)
SUB_COM2-S
SUB_COM2-R1 -- --
(reserved) (
∗
)
SUB_COM3-S
SUB_COM3-R1 -- --
-- --
SUB_COM4-S
SUB_COM4-R1 -- --
-- --
SUB_COM5-S
SUB_COM5-R1 -- --
Send signal
name
Send
command
Receive
command
Receive signal
name
Asigned
by PLC
Asigned
by PLC
Содержание GRL150-100 Series
