Toshiba e-studio 167 Скачать руководство пользователя страница 75

Страница: 75 / 268

e-STUDIO167/207/237

GENERAL OPERATION

4 - 7

(B) Pick-up failure in bypass

• When paper becomes almost empty as they fed out during copying,

The tray-up sensor is turned OFF.

The tray-up motor is turned ON – the tray is raised.

The tray-up sensor is turned ON.

The tray-up motor is stopped.

• When the paper empty sensor is turned OFF even if the tray-up sensor is ON during copying,

The sensor is detecting that no paper exists.

The lamp on the control panel corresponding to the drawer blinks (When the drawer is
selected)

Copying is stopped

• During bypass feeding

Bypass pickup solenoid ON

Registration sensor is not turned ON in a fixed period of time

“Misfeed in bypass“ is displayed : E12

Copying operation is disabled

Solution: The bypass paper sensor is turned OFF by removing the paper from the bypass tray.

Содержание e-studio 167

























































































































































































































































Результаты поиска

Содержание e-studio 167

Отзывы:

Toshiba e-studio 167, Руководство по обслуживанию, Страница: 75 / 268

Результаты поиска

Содержание e-studio 167

Отзывы: