Toshiba e-studio 167 Скачать руководство пользователя страница 204

Страница: 204 / 268

e-STUDIO167/207/237

DEVELOPMENT SYSTEM

12 - 10

2) Function of auto-toner sensor

- The auto-toner sensor consists of the following circuits:

Drive winding:
A magnetic head (primary side) with a high-frequency magnetic field, which forms a magnetic cir-
cuit in the developer material.

Detection winding:
Receives the change in the magnetic resistance of the developer material through the magnetic
circuit (secondary side).

DC conversion circuit:
Converts a high-frequency output from the detection winding into a DC signal (auto-toner output
V

ATS

Fig. 12-5

- When the toner density is low

The ratio of the toner against the carrier in the developer material decreases.

→

The magnetic resistance decreases.

→

The detection output increases.

→

The auto-toner output V

ATS

increases.

- When the toner density is high

The ratio of the toner against the carrier in the developer material increases.

→

The magnetic resistance increases.

→

The detection output decreases.

→

The auto-toner output V

ATS

decreases.

Developer material

Magnetic resistance

Drive

winding

Detection

winding

conversion

circuit

Auto-toner sensor

output

To the A/D converter

(MAIN board)

ATS-1A

Magnetic circuit

Magnetic resistance

Developer material

Содержание e-studio 167

























































































































































































































































Результаты поиска

Содержание e-studio 167

Отзывы:

Toshiba e-studio 167, Руководство по обслуживанию, Страница: 204 / 268

Результаты поиска

Содержание e-studio 167

Отзывы: