Toshiba e-studio 167 Скачать руководство пользователя страница 237 | Manualshive

Страница: 237 / 268

Toshiba e-studio 167 Скачать руководство пользователя страница 237

13

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

FUSER / EXIT UNIT

13 - 21

[J] Fuser thermostat (THMO1)

[K] Exit motor (M7): Option

Note:

When installing the thermistors, do not mix
up the installation positions of the side ther-
mistor and the edge thermistor by telling
them apart by the length of their harnesses.

Fig. 13-32

(1) Take off the fuser roller.

P.13-18 "[G] Fuser roller"

(2) Remove 2 screws and take off the fuser ther-

mostat.

Fig. 13-33

(1) Take off the rear cover.

P.2-22 "[J] Rear cover"

(2) Disconnect 1 connector, remove 1 screw,

and then take off the exit motor with the
bracket while sliding it toward the right.

Fig. 13-34

Center thermistor

Side thermistor

Edge thermistor

Fuser thermostat

Connector

Bracket

Exit motor

Screw

«
...
235
236
237
238
239
...
»

Содержание e-studio 167













































































































































































































































































Отзывы:

Нет отзывов