Toshiba e-studio 167 Скачать руководство пользователя страница 29

Страница: 29 / 268

e-STUDIO167/207/237

OUTLINE OF THE MACHINE

2 - 13

5) PC boards

6) Lamps and heaters

Symbol

Name

Function

Remarks

P-I

MAIN

PWA-F-MAIN

Main PC board (MAIN board)

Controlling the whole system and

image processing

Fig. 2-7

7-1

SRAM

PWA-F-SRAM

SRAM PC board (SRAM board)

Storing the setting information of the

equipment

Fig. 2-7

7-33

LDR

PWA-F-LDR

Laser driving PC board (LDR board)

Driving the laser diode

Fig. 2-5

5-13

SNS

PWA-F-SNS

H-sync signal detection PC board

(SNS board)

Detecting the laser beam position

Fig. 2-5

5-13

HPNL

PWA-F-HPNL

Control panel PC board

(HPNL board)

Detecting the button entry and control-

ling LED and LCD on the control panel

Fig. 2-3

4-20

CTIF

PWA-F-CTIF

Toner cartridge interface PC board

(CTIF board)

Interface for detecting the toner car-

tridge

(Detecting the CTRG board)

Fig. 2-5

7-30

CTRG

PWA-F-CTRG

Toner cartridge PC board

(CTRG board)

Storing the status of the toner cartridge

Fig. 2-5

103-3

FUS

PWA-F-FUS

Fuse PC board (FUS board)

Supplying power to each damp heater

Optional for NAD/MJD/CND model,

standard for other models

Fig. 2-6

7-12

PFC

PWA-F-PFC

Paper feed controller PC board

(PFC board)

Controlling the automatic duplexing unit

and paper feed pedestal

Option

Fig. 2-7

7-35

ADU

PWA-F-ADU

ADU driving PC board (ADU board)

Controlling the automatic duplexing unit

Option

Fig. 2-9

MD-0103

1-13

Symbol

Name

Function

Remarks

P-I

LAMP1 CNTR-LAMP

Center heater lamp

Heating the center section of the fuser

roller

Fig. 2-5

23-12

LAMP2 SIDE-LAMP

Side heater lamp

Heating the section of both sides of the

fuser roller

Fig. 2-5

23-13

ERS

LP-ERS

Discharge LED

Removing the residual charge from the

drum surface

Fig. 2-6

20-13

DH1

SCN-DH-L

Scanner damp heater (Left)

Preventing condensation in the scan-

ner unit

Optional for NAD/MJD/CND model,

standard for other models

Fig. 2-3

9-17

DH2

SCN-DH-R

Scanner damp heater (Right)

Preventing condensation in the scan-

ner unit

Optional for NAD/MJD/CND model,

standard for other models

Fig. 2-3

9-18

DH3

DRM-DH

Drum damp heater

Preventing condensation of the drum

Optional for NAD/MJD/CND model,

standard for other models

Fig. 2-6

8-6

Содержание e-studio 167

























































































































































































































































Результаты поиска

Содержание e-studio 167

Отзывы:

Toshiba e-studio 167, Руководство по обслуживанию, Страница: 29 / 268

Результаты поиска

Содержание e-studio 167

Отзывы: