Toshiba e-studio 167 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 268

Toshiba e-studio 167 Скачать руководство пользователя страница 70

e-STUDIO167/207/237

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

GENERAL OPERATION

4 - 2

4.2

Description of Operation

4.2.1

Warming-up

1) Initialization

Power ON

→

Heater lamp ON

→

“Please wait” is displayed

→

Fan motors ON

→

Initialization of scanning system

- The CIS unit moves to the home position.
- The CIS unit moves to the peak detection position.
- The LED of CIS is turned ON.
- Peak detection (white color is detected by the shading correction plate)
- The LED of CIS is turned OFF.
- The CIS unit moves to the home position.

→

“READY (WARMING UP)” is displayed

2) Pre-running operation (Only when the temperature is at 16 °C or less)

The pre-running operation is started when the temperature of the fuser roller surface reaches a cer-
tain temperature.

→

The main motor is turned ON

- Fuser roller rotated.
- Drum rotated.

→

Pre-running operation stops after 15 seconds

3) When the surface temperature of the fuser roller becomes sufficient for fusing,

→

“READY” is displayed

4.2.2

Ready state (ready for copying)

Buttons on the control panel enabled

→

When no button is pressed for a certain period of time,

- Set number “1” is displayed. Equipment returns to the normal ready state.

«
...
68
69
70
71
72
...
»

Содержание e-studio 167













































































































































































































































































Отзывы:

Нет отзывов