Toshiba e-studio 167 Скачать руководство пользователя страница 72

Страница: 72 / 268

e-STUDIO167/207/237

GENERAL OPERATION

4 - 4

4.2.4

Bypass feed copying

1) Insert a sheet of paper into the bypass tray.

→

Bypass paper sensor ON

- Bypass feed priority state.

2) Press the [START] button

→

“READY” Æ “COPYING”

→

CIS LED ON

→

Scan motor ON

→

CIS unit move forward

→

Polygonal motor rotates in high speed

→

Main motor and exit motor ON

- The drum, fuser unit, developer unit and exit roller are driven.

3) Bypass feeding

→

Main charger, developer bias and discharge LED ON. Fans are rotated in high speed.

→

Bypass pickup solenoid ON

- The bypass pickup roller start to rotate.
- The bypass pickup roller is lowered.
- The bypass feed roller start to rotate.

→

Paper reaches the registration roller

→

Aligning operation

→

After a certain period of time, the bypass pickup solenoid OFF

4) Hereafter, the operation 3) through 6) of

P.4-3 "4.2.3 Drawer feed copying" is repeated.

4.2.5

Interruption copying

1) Press the [INTERRUPT] button

→

LED “INTERRUPT” ON

→

Copying operation in progress is temporarily stopped. CIS unit return to appropriate positions

→

“Job interrupted” is displayed

→

Automatic density and reproduction ratio 100% are set (The set number remains the same)

2) Select the desired copy condition

3) After the interruption copying is finished:

→

LED “INTERRUPT” OFF by pressing the [INTERRUPT] button

→

“READY to resume job” is displayed

4) Press the [START] button

→

The copying operation before the interruption is resumed

Содержание e-studio 167

























































































































































































































































Результаты поиска

Содержание e-studio 167

Отзывы:

Toshiba e-studio 167, Руководство по обслуживанию, Страница: 72 / 268

Результаты поиска

Содержание e-studio 167

Отзывы: