Toshiba e-studio 167 Скачать руководство пользователя страница 257

Страница: 257 / 268

e-STUDIO167/207/237

POWER SUPPLY UNIT

15 - 3

15.3 Output Channel

The following are 6 output channels for the main switch line.

1) +5V

+5V:

CN104

Pin 3

Output to the MAIN board

+5V:

CN112

Pins 3 and 4

Output to the PFC board, ADU (via PFC board), PFP (via PFC board)

+5VB:

CN104

Pin 8

Output to the FUS board

+5VB:

CN104

Pins 9 and 10

Output to the MAIN board

2) +12V

+12V:

CN110

Pin 3

Output to the FAX unit

3) -12V

-12V:

CN104

Pin 2

Output to the control panel (via MAIN board)

-12V:

CN110

Pin 2

Output to the FAX unit

4) +24V

+24V:

CN104

Pins 19 and 20

Output to the MAIN board, PFU (via MAIN board)

+24V:

CN112

Pins 1 and 2

Output to the PFC board, ADU (via PFC board), PFP (via PFC board)

+24VDF:

CN104

Pins 17 and 18

Output to the RADF/ADF (via MAIN board)

The following is an output channel for the cover switch line.

1) +24V

+24VCOV-OFF:

CN104

Pins 23 and 24

Output to the MAIN board

Содержание e-studio 167

























































































































































































































































Результаты поиска

Содержание e-studio 167

Отзывы:

Toshiba e-studio 167, Руководство по обслуживанию, Страница: 257 / 268

Результаты поиска

Содержание e-studio 167

Отзывы: