Toshiba e-studio 167 Скачать руководство пользователя страница 222 | Manualshive

Страница: 222 / 268

Toshiba e-studio 167 Скачать руководство пользователя страница 222

e-STUDIO167/207/237

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

FUSER / EXIT UNIT

13 - 6

13.5 Fuser Unit Control Circuit

13.5.1

Configuration

In this equipment, the surface temperature of the fuser roller is controlled by turning ON/OFF 2 heater
lamps (center and side) which have different heat-generating positions with the command from the SoC
on the MAIN board. The surface temperature of the fuser roller is detected by 3 thermistors (center,
side and edge) and then the information of the temperature is transmitted to the SoC and each control
circuit. Based on the detected temperature, the SoC transmits the control signal of the heater lamp to
the control circuit (TRC: Triac) of each heater lamp on the switching regulator. The power supply to
each fuser roller is thus controlled by driving TRC. The SoC detects the overheating of the fuser roller.
In case that the surface temperature of the fuser roller has exceeded the specified temperature, the
SoC turns the heater lamp OFF.
If the SoC does not function for some reason and the fuser roller is abnormally overheated as the
result, a forcible power-OFF circuit transmits a relay-OFF signal to the switching regulator to shut off the
power supply to the heater lamp by opening the relay. In addition, if these control circuits do not func-
tion with thermistor abnormality or other reasons and the fuser roller is abnormally overheated as the
result, thermostat shut off the power supply to the heater lamps to protect the equipment.

Fig. 13-2

Main switch

Forcible power-off

circuit

A/D

converter

SoC

Side heater lamp

Center heater lamp

Fuser roller

Fuser thermostat

Edge
thermistor

Side
thermistor

Center
thermistor

Center heater lamp

control circuit

(TRC1)

Side heater lamp

control circuit

(TRC2)

Noise

filter

AC line

DC line

Fuser unit

Center heater lamp
control signal

Side heater lamp
control signal

Relay-OFF signal

MAIN board

L

N

Switching regulator

Front

Rear

Relay

«
...
220
221
222
223
224
...
»

Содержание e-studio 167













































































































































































































































































Отзывы:

Нет отзывов