Toshiba e-studio 167 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 268

Toshiba e-studio 167 Скачать руководство пользователя страница 74

e-STUDIO167/207/237

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

GENERAL OPERATION

4 - 6

4.3.2

Description of abnormality

(A) Add paper

[In cases of the equipment drawer or the PFU / PFP drawer ] (When drawer is not installed)
• Drawer empty sensor detects the presence or absence of paper.

No drawer detected

“Add paper” is displayed
The LED on the control panel corresponding to the drawer blinks (When the drawer is selected)

[START] button disabled

[In cases of the equipment drawer or the PFU drawer] (When the drawer is installed)

Drawer detected

Paper empty sensor OFF

“Add paper” is displayed
The LED on the control panel corresponding to the drawer blinks (When the drawer is selected)

[START] button disabled

[In case of the PFP drawer] (When the drawer is installed)
• When the power is turned ON or the drawer is installed

PFP starts initialization

The detection of paper existence starts
Tray-up motor ON – Tray is raised

At this time, the tray-up sensor and paper empty sensor are OFF

When the tray-up sensor is not turned ON in a fixed period of time

Tray abnormality “Add paper” is displayed regardless of the existence of paper

Cleared by turning the power ON and then OFF
The tray-up sensor is turned ON in a fixed period of time

- The tray-up motor is stopped.
At this time, if the paper empty sensor is

ON: It is judged that there is paper
OFF: It is judged that there is no paper

The lamp on the control panel corre-
sponding to the drawer blinks (When
the drawer is selected)

«
...
72
73
74
75
76
...
»

Содержание e-studio 167













































































































































































































































































Отзывы:

Нет отзывов