Toshiba B-EX6T Series Скачать руководство пользователя страница 134

Страница: 134 / 160

133

B-EX4T1

・

B-EX700-RFID-U2-EU/US-R

・

B-EX700-RFID-U4-R

・

B-EX700-RFID-U4-EU/US/AU-R

・

U4 module preinstall model (B-EX4T1/T2-GS18/TS18-CN-R)

9.10.4.4 WRITE AGC THRESHOLD

Max.

value

Min. value

Step

Display

Sign

Integer

digit

Decimal

place

0-padding

Unit of

measure

Decimal

None

When the Q value is set to 1 or above, the AGC threshold for data write becomes effective.

When the obtained gain of an RFID tag is lower than the AGC threshold for data write, a data write operation

is not performed. In other words, setting an AGC threshold for data write enables writing data only to a tag

placed just above the antenna.

Supposing that the gain of a tag just above the antenna is 14 and that of a tag off the antenna is 7, setting

the threshold to 11 (a value between 8 and 14) enables the printer to write data only to the tag just above the

antenna.

When the threshold is set to 0, a data write operation is performed regardless of the gain of a tag.

Both of the AGC threshold and the AGC threshold for data write are used to determine whether a tag is

defective or not, but the timing of a gain measurement is different. In the case of the AGC threshold, this is

performed after data is written to a tag. On the contrary, when the AGC threshold for data write is effective a

measurement is performed before data is written. And if a gain value is lower than the threshold, a data write

operation is not performed.

The optimum value differs depending on the tag type.

Actually, the problem of reading multiple tags at the same time does not occur with most RFID tag types. It

is not necessary to change the default setting of

“0”.

Note: This is effective only for the following modules:

B-EX6T1/T3

・

B-EX706-RFID-U4-R

・

B-EX706-RFID-U4-EU/US/AU-R

B-EX4T1

・

B-EX700-RFID-U2-EU/US-R

・

B-EX700-RFID-U4-R

・

B-EX700-RFID-U4-EU/US/AU-R

・

U4 module preinstall model (B-EX4T1/T2-GS18/TS18-CN-R)

9.10.4.5 WRITE RETRY MIN AGC

Max.

value

Min. value

Step

Display

Sign

Integer

digit

Decimal

place

0-padding

Unit of

measure

Decimal

None

When the Q value is set to 1 or above, the AGC threshold lower limit for retry becomes effective.

In the case the printer could not find any tag whose gain is over the AGC threshold for data write, the AGC

threshold is lowered to the highest gain of the detected tags whose gains are over the AGC threshold lower

limit for retry specified with this parameter.

Example 1

AGC threshold for data write: 11
Lower limit for retry: 9
Detected tag’s gain: 10

Содержание B-EX6T Series

































































































































































Результаты поиска

Содержание B-EX6T Series

Отзывы:

Похожие инструкции для B-EX6T Series

Бренды по названию

Популярные бренды

Toshiba B-EX6T Series, Спецификация ключевых операций

Результаты поиска

Содержание B-EX6T Series

Отзывы:

Похожие инструкции для B-EX6T Series

Бренды по названию

Популярные бренды