Toshiba B-EX6T Series страница 159 Скачать руководство пользователя

Страница: 159 / 160

158

13 Power Save Function

1. Printer status allowing shift to the power save mode

When the following status continues for a specified length of time, the printer will enter the power save mode

and show the power save mode message. (Refer to 5. Power save mode display described below.)



ONLINE (Idle, communicating)



Pause



Error



Waiting for removal of a label from the media outlet



System mode (except for the menus that use the 27V line, such as self-diagnosis, test print and sensor

adjustment.)



User system mode (except for the menus that use the 27V line, such as dumping.)



Pause of the expansion I/O

2. Conditions for exiting the power save mode

The power save mode is terminated when:



Printing is performed.



Printing operation with restart key.



Feed/Reprint operation with feed key



The status of the expansion I/O pause signal or active signal changes (because the message indicating a

pause state is displayed on the LCD.)



Printing or paper feed is initiated through the expansion I/O, or printing is caused by a release of the printer

from the pause state instructed through the expansion I/O



The printer receives U1/U2 command (Forward feed/reverse feed command).



The printer receives T command (Feed command).



The printer receives XS command (Issue command).



The printer receives IB command (Eject command).



The printer receives RFID-related command accompanied by printer action



The head lever is locked/unlocked (because the message notifying the head lever unlock state is displayed

on the LCD.)



Automatic calibration is performed with the head lever locked.



Up and down of the solenoid is tested during the Factory Test menu in the system mode.



Sensor adjustment is performed in the system mode.

3. Display and key operations during the power save mode

When the printer enters the power save mode, it shows

“POWER SAVING MODE” on the LCD and turns off

the LCD backlight. However, the operations mentioned in 6 enable the printer to display usual messages and

turn on the LCD backlight even in the power save mode. If the printer status remains unchanged for 30

seconds,

“POWER SAVING MODE” is displayed and the LCD backlight turns off again.

4. LED during the power save mode

While the printer is in the power save mode, the state of the LEDs is as follows.



ONLINE LED: Flashes (ON: 1000msec. OFF: 1000msec.)



ERROR LED: OFF

Содержание B-EX6T Series

































































































































































Результаты поиска

Содержание B-EX6T Series

Отзывы:

Похожие инструкции для B-EX6T Series

Бренды по названию

Популярные бренды

Toshiba B-EX6T Series, Спецификация ключевых операций

Результаты поиска

Содержание B-EX6T Series

Отзывы:

Похожие инструкции для B-EX6T Series

Бренды по названию

Популярные бренды