manualshive.com logo in svg

TORXUN AUTOPED M10S.0028, Руководство по установке, Страница: 9 / 82

Поделиться
Скачать
TORXUN AUTOPED M10S.0028 Скачать руководство пользователя страница 9

Autoped Installation Manual rev 2.0 (100722)

                                                                                                                                                                                                            

9 

 

IMPORTANT INSTALLATION NOTES 

 
 

A. CONVERSION: LEFT-HAND INSTALLATION TO RIGHT-HAND INSTALLATION

 (or vice versa) 

The AutoPed operator can be used in a left-hand or right-hand, push or pull door/gate system application without need for 
conversion adapters or modification. To change the Hand of the Operator Installation

: 

•

 Remove the motor-drive assembly attached to the assembly plate from the chassis by removing the 

six (6) M6x12 bolts; Fig 1 

•

 Rotate the assembly plate with the motor-drive clockwise or counter-clockwise to facilitate 

either left- or 

– right-hand installation. 

•

 Chassis is neutral, Orientation is the same for left- or right- hand installation 

•

 Left-hand operator installation: Control unit is to the left of the motor-drive 

•

 Right-hand operator installation: Control unit is to the right of the motor-drive 

 

Fig I.1 Changing Operator Installation:  Left-hand to Right-hand or vice versa 

 

 

 
 
 
 
 
 

Содержание AUTOPED M10S.0028



















































































Отзывы:

Нет отзывов