TORXUN AUTOPED M10S.0028 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 82

TORXUN AUTOPED M10S.0028 Скачать руководство пользователя страница 49

Autoped Installation Manual rev 2.0 (100722)

49

XI.5 REATTACH THE CONTROL BOX AND OPERATOR FRONT COVER

a. Reattach front plastic cover of Control Box

After the unit has been cycled a few times and your ANSI checklist has been completed, reattach the plastic cover onto the
control unit. Align the gaskets into the cut outs so that they sit flush. Tighten the two provided screws into the threaded
sections of the control board. Give the cover a slight tug to make sure that it is secured properly.

⚠

Do not over tighten the

cover.

⚠

Make sure that the grommets are completely seated in the cut outs on both ends and sealed properly within the

groove.

b. Reattach the operator Front Cover

There are two knock outs on the Front Cover that will correspond with the arm coming from the gearbox. Remove the
appropriate knock out for the location of the arm and slide the front cover onto the operator. Secure the front cover to the
chassis with the four (4) thumb screws. Tighten the thumb screws by hand until the front cover is secured to the chassis.

«
...
47
48
49
50
51
...
»

Содержание AUTOPED M10S.0028



















































































Отзывы:

Нет отзывов