Toro Z Master 500 Series Скачать руководство пользователя страница 84

Страница: 84 / 168

5-13

Z Master 500 Gas Series Service Manual

ENGINE

12. Install the battery negative cable to the battery.

13. Test operate engine; adjust choke and throttle cables

as required. Check engine low and high idle are to

specification.

Fig 200

DSC-2973

11. Install the engine air cleaner cover on the engine

Fig. 200).

Note: This unit has a standard air cleaner assembly.

28 HP Kohler EFI Air-Cooled Engine

Removal

Note: If welding on an EFI equipped machine, be

sure to disconnect the negative ground cable

on the battery and disconnect the ECU.

1. Disconnect the negative battery cable from the

battery.

Fig 201

DSC-2883

3. Loosen and remove the bolt, spacer, spring, and nut

retaining the air cleaner assembly to the air cleaner

bracket (Fig. 202).

Fig 202

DSC-2884

2. Loosen the hose clamp on the air intake hose (Fig.

201).

Содержание Z Master 500 Series









































































































































































Результаты поиска

Содержание Z Master 500 Series

Отзывы:

Toro Z Master 500 Series, Руководство по обслуживанию, Страница: 84 / 168

Результаты поиска

Содержание Z Master 500 Series

Отзывы: