Toro Z Master 500 Series Скачать руководство пользователя страница 59

Страница: 59 / 168

4-10

Z Master 500 Gas Series Service Manual

3. Install the two bolts, short spacers, lock washers,

and nuts through the wheel motor, brake linkage and

the frame (Fig. 131).

Fig 131

DSC-3082

HYDRAULIC SYSTEM

Fig 128

DSC-3079

A. Front Spacer (short)

B. Back Spacer (long)

Fig 130

DSC-3081

2. Align the brake linkage with the two front bolt holes

(Fig. 130).

Fig 129

DSC-3080

1. Install wheel motor in the frame. Loosely install the

back two bolts, long spacers, lock washers and nuts

(Fig. 129).

Note: There are two different spacers used on the

wheel motors (Fig. 128). The short spacers

are used in the front of the wheel motors(with

the brake linkage) and the long spacers are

used to retain the back of the wheel motor.

Содержание Z Master 500 Series









































































































































































Результаты поиска

Содержание Z Master 500 Series

Отзывы:

Toro Z Master 500 Series, Руководство по обслуживанию, Страница: 59 / 168

Результаты поиска

Содержание Z Master 500 Series

Отзывы: