manualshive.com logo in svg

Toro Z Master 500 Series, Руководство по обслуживанию, Страница: 139 / 168

Поделиться
Скачать
Toro Z Master 500 Series Скачать руководство пользователя страница 139

7-2

Z Master 500 Gas Series Service Manual

7

MOWER DECKS/PTO

Electric PTO Clutch Removal

The electric PTO clutch removal and installation are 

similar on both the air cooled engine models and the 

liquid cooled model. The only difference is the clutch 

guard removal. The figure below points to the bolts 

that need to be removed in both units (Fig. 355). The 

procedure shows an air-cooled unit.

 

Fig 355

 

DSC-3131

On the Kawasaki liquid cooled models, remove 6 bolts to 

access the clutch (Fig. 356).

 

Fig 356

 

DSC-3794

 

Fig 358

 

DSC-3134

2.  Remove the right and left top bolt and nut on the top 

strap guards to remove the clutch guard from the 

unit (Fig. 358).

 

Fig 357

 

DSC-3131

This procedure is on the Air Cooled Engine Models and 

follows the same procedure for the Liquid Cooled Engine 

Model.

1.  Loosen and remove 2 bolts and nuts located on the 

clutch guard (Fig. 357).

A

A

B

B

A.  Top strap bolts 

B.  Clutch guard bolts

Содержание Z Master 500 Series









































































































































































Отзывы:

Нет отзывов