Toro Z Master 500 Series Скачать руководство пользователя страница 18

Страница: 18 / 168

2-9

Z Master 500 Gas Series Service Manual

SPECIFICATIONS

Cutting Decks

Configuration

Side discharge, mid-mounted rotary with three blades.

Construction

7 gauge, high strength 50,000 psi steel, 5-1/2” deep, advanced, super flow system, welded

construction. 3/8” steel discharge reinforcement plate doubles as bagger attachment point.

Discharge

Right hand as viewed from operator seat. Rubber chute, spring biased down toward

operating position. Adjustable flow control baffle.

Blade Tip Speed

18,000 + ft/min at high idle

152cm mower – 4600.7 m/min @3000 RPM

Height of Cut

Adjustable from the seat with range 1.5” – 5” in 1/4” increments (3.8cm - 12.7cm)

Deck Suspension

Deck suspended from machine by four lift chains, and attached to rear wheel supports by

two struts.

Belt Covers

16-gauge, formed steel covers. Attached with swell latches.

Gauge Wheels

52” Cutting Deck – Five adjustable gauge wheels to reduce scalping: three on front of

deck (one on left-hand side and two in center) and two on rear of deck (left and right

sides). Wheels have four adjustment positions.
60”, 72”, and 152cm Cutting Decks – Six adjustable gauge wheels to reduce scalping: four

on front of deck (one each left-hand and right-hand sides, and two center) and two on rear

of deck (left and right sides). Wheels have four positions.

Lubrication Fittings:

Front Castor Pivots 2 removable plugs (1 per side) for periodic lubrication.
Front Castor

Wheels

2 fittings (1 per side).

Lift Assembly

5 fittings.

Mule Drive Idler

1 fitting.

Brake Arms

2 fittings (1 per side).

Rear Deck Struts

2 fittings (1 per side).

Deck Spindles

3 fittings (1 per spindle).

Hydraulic Pump

Drive Tensioner

1 fitting.

Содержание Z Master 500 Series









































































































































































Результаты поиска

Содержание Z Master 500 Series

Отзывы:

Toro Z Master 500 Series, Руководство по обслуживанию, Страница: 18 / 168

Результаты поиска

Содержание Z Master 500 Series

Отзывы: