Toro Z Master 500 Series Скачать руководство пользователя страница 114

Страница: 114 / 168

5-43

Z Master 500 Gas Series Service Manual

ENGINE

Fig 318

DSC-2847

11. Remove the 4 bolts, washers, and nuts retaining the

fan assembly to the fan mounting plate assembly

(Fig. 318).

Fig 317

DSC-2845

10. There are 6 bolts and washers located under the

radiator retaining the radiator to the fan mounting

plate. Remove all 6 bolts and washers. Remove the

radiator (Fig. 317).

Fig 320

DSC-2849

13. Remove the fan assembly through the front opening

of the radiator support (Fig. 320).

Fig 319

DSC-2848

12. Before removing the fan assembly, remove two

clamps located on the upper engine air duct.

Remove the engine air intake duct (Fig. 319).

Reverse the order of removal.

Cooling Fan Assembly Installation

Note: Fan removed for clarity.

Содержание Z Master 500 Series









































































































































































Результаты поиска

Содержание Z Master 500 Series

Отзывы:

Toro Z Master 500 Series, Руководство по обслуживанию, Страница: 114 / 168

Результаты поиска

Содержание Z Master 500 Series

Отзывы: