Toro Z Master 500 Series Скачать руководство пользователя страница 4

Страница: 4 / 168

Z Master 500 Gas Series Service Manual

TABLE OF CONTENTS

SAFETY INFORMATION

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Think Safety First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SPECIFICATIONS

Kawasaki Liquid Cooled Product Shots . . . . . . . . . . . . . . . . . . . . . . . . .

Kohler EFI Product Shots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Kohler Gas Product Shots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Kawasaki Gas Product Shots . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Traction System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Deck Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cutting Decks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General Specifications

Greasing and Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model and Serial Number Locations . . . . . . . . . . . . . . . . . . . . . . . . .

Available Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Standard Torque for Dry, Zinc Plated, and Steel Fasteners (Inch Series) . . . . . . . . . . . .

Standard Torque for Dry, Zinc Plated, and Steel Fasteners (Metric Fasteners) . . . . . . . . . .

Other Torque Specifications

SAE Grade 8 Steel Set Screws . . . . . . . . . . . . . . . . . . . . . . . . . . .

Thread Cutting Screws (Zinc Plated Steel) . . . . . . . . . . . . . . . . . . . . . .

Wheel Bolts and Lug Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Thread Cutting Screws (Zinc Plated Steel) . . . . . . . . . . . . . . . . . . . . . .

Equivalents and Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

US to Metric Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CHASSIS

Caster Fork Assembly Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Replacing the Caster Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Caster Fork Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front Wheel Removal and Bearing Replacement . . . . . . . . . . . . . . . . . . . . .

Fuel Tank Removal

Left Side Fuel Tank Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Left Side Fuel Tank Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .

Right Side Fuel Tank Removal and Installation . . . . . . . . . . . . . . . . . . . . .

Hood Assembly Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hood Assembly Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brake Lever Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brake Lever Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brake Band Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brake Band Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brake Shaft Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brake Shaft Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjusting the Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Deck Lift Lever Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Deck Lift Lever Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2

2-2

2-3

2-4

2-5

2-6

2-7

2-8

2-9

2-10

2-11

2-12

2-13

2-14

2-15

2-16

2-17

3-2

3-4

3-5

3-6

3-7

3-8

3-10

3-11

3-13

3-17

Содержание Z Master 500 Series









































































































































































Результаты поиска

Содержание Z Master 500 Series

Отзывы:

Toro Z Master 500 Series, Руководство по обслуживанию, Страница: 4 / 168

Результаты поиска

Содержание Z Master 500 Series

Отзывы: