manualshive.com logo in svg

Toro Z Master 500 Series, Руководство по обслуживанию, Страница: 35 / 168

Поделиться
Скачать
Toro Z Master 500 Series Скачать руководство пользователя страница 35

3-8

Z Master 500 Gas Series Service Manual

3

CHASSIS

1.  Unhook the two rubber latches located on the rear of 

the hood.

2.  Remove the two hairpins, clevis pins, and washers 

located in the front left and right lower side of the 

hood (Fig. 044).

Hood Assembly Removal

3.  Lift the hood and remove the stop lanyards located 

on each side of the hood. Remove the hood from the 

frame of the unit (Fig. 045).

 

Fig 045

 

DSC-1581

Hood Assembly Installation

Reverse the order of removal.

 

Fig 044

 

DSC-1579

1.  Release the parking brake (forward position).

2.  Remove the cotter pin and clevis pin from the brake 

rod yoke (Fig. 046).

Brake Lever Removal

 

Fig 046

 

DSC-1618

3.  Lift the floor pan assembly to access the brake lever 

shaft and cotter pin (Fig. 047).

 

Fig 047

 

DSC-1619

Содержание Z Master 500 Series









































































































































































Отзывы:

Нет отзывов